ASIC Repair Basics: Antminer S17+ Common Faults and Solutions

The Antminer S17+ is a robust and powerful ASIC miner designed for the SHA-256 algorithm. It offers excellent efficiency with its advanced cooling system and low power consumption. The S17+ can reach up to 73 TH/s hash rate and has an energy efficiency of around 40 J/TH. Common faults that may occur on the device include overheating, errors in voltage regulation, faulty MOS chips, or problems with the temperature sensor chip. Fortunately, these issues can usually be resolved by troubleshooting or replacing parts as needed.

Overview of Antminer S17+ and Common Faults

The Antminer S17+ has the potential to keep your mining operations going strong, but it’s essential to be aware of common issues that could affect its performance. From overheating and voltage regulation problems to faulty MOS chips and temperature sensor chip malfunctions, these components can cause significant setbacks if not correctly managed. By understanding which parts are most prone to failure in an S17+, you’ll have a better chance of keeping any downtime from happening!

BM1397 chips

A miner’s success or failure can come down to a single chip. BM1397 ASIC chips are like the beating heart of any mining machine, powering its calculations for optimal hash rates and cryptocurrency yields with their immense computing power. When combined beneath a heatsink that copes with intense temperatures, these 65 marvels represent hope – but also vulnerability; if one of them is damaged in any way, miners will be left helplessly struggling against diminishing returns.

CT1F: All your signal are belong to us

Location: U1, U2

Situated in the upper right corner of its hash board, SN74LVC1T45DBVR CT1F is a 6-pin dual power bus transceiver chip IC that boasts SOT-23-6 packaging technology. Withstanding temperatures from -40°C up to +80°C and operating on voltages between 1.65V and 5.5V, two powerful chips are included in each hashboards.

PIC16F1704: Checking PIC Circuits

Location: U3

Leverage the PIC16F1704 8-bit microcontroller to ensure your circuit’s performance is up to specifications. Quickly detect when a pin voltage fails and reprogram with relative ease after verifying that cables connected between test fixtures and Hash boards are working correctly.

ATH93702DMCN: Serial Electrically Erasable Programmable Read-Only Memory

Location: U5

The ATH93702DMCN EEPROM chip is an invaluable tool for any mining rig setup. Shielding you from malicious hacking attempts and boasting remarkable programmability up to 100,000 times – this trusted sidekick ensures long-term reliability with minimal disruption in power consumption.

TPHR9003NL: Voltage Output in the Voltage Domain

Location: Q1

Q1 (TPHR9003NL) is a special MOS chip that checks voltage output in the voltage domain. It features a two-way data transmission protocol for extensive data storage, enabling reliable operation with high accuracy, low heat generation and minimal current consumption. Moreover, it is constructed with advanced technologies such as reduced switching losses and fast transient response times, providing maximum efficiency and stability even under extreme environmental conditions.

MP1517DR: Boost Converter Chip for Noise Reduction and Efficiency

Location: U6

The MP1517DR boost converter chip is located in the upper left corner of the back of the hashboard. It offers high switching frequency, fast response times and low start-up current requirements for efficient noise reduction and increased power conversion efficiency. It can also help reduce system costs by eliminating costly external components.

AP431SAN1TR-G1: 3-Terminal Adjustable Shunt Regulator with SOT23 Packaging Technology

Location: U4

The AP431SAN1TR-G1 is an efficient, low-power 3-terminal adjustable shunt regulator with SOT23 packaging technology. It features sharp turn-on characteristics with a low minimum cathode current for regulation, a wide input/output range and built-in thermal protection to extend its life. Its internal soft start circuit reduces inrush current during start-up periods making it an ideal choice for designers.

MP2019K3869253MPSK34: Low Quiescent Current Adjustable Output Linear Regulator

Location U28

The U28 (MP2019K3869253MPSK34) is a high-quality linear regulator with a low quiescent current and an input voltage range of 3V to 40V. It has excellent stability, temperature characteristics and small size, making it an ideal choice for powering ASIC mining hardware with superior power efficiency and low output noise.

SGM2036-ADJ: Low Power, Low Dropout, CMOS Linear Regulator

Location: U127

The SGM2036-ADJ is a low-power, low-dropout CMOS linear regulator perfect for applications that require minimal power consumption. It offers an array of protection features ensuring high reliability and making it suitable for various extreme conditions.

SY8120I: High-Efficiency Synchronous Step-Down DC/DC Converter

Location: U128

The SY8120I is an efficient step-down DC/DC converter perfect for low voltage, low power applications. Its main and synchronous switches have very low RDS(ON) to minimize conduction losses and its wide input voltage range from 1.6V to 5.5V makes it suitable for various uses. Reliable performance in extreme conditions makes it an ideal choice for miners.

NCT218: Temperature Sensor Chip with Dual Channel Digital Thermometer

Location: U120

The U120(NCT218) temperature sensor chip offers precise readings with a high accuracy rate of ±1.75°C and a low power consumption rate, making it an ideal choice for successful mining operations over a wide temperature range of -40°C to +125°C.

How to use hash board code editor for EEPROM chip programming errors

For those who have encountered EEPROM chip programming errors on their S17+ hash board, the hash board code editor can be used to re-flash the EEPROM file and restore it back to normal. This article will provide an overview of the steps required for using this tool to troubleshoot such errors.

Troubleshooting Pattern NG error in the log

When a Pattern NG error appears in the testing fixture’s log, several methods exist to troubleshoot it. Firstly, the hash board code editor should be used to re-flash the hash board’s EEPROM file. This can often have a positive effect as the EEPROM chip stores operation information for the ASIC chips – so if anything is abnormal, it may affect the chip’s hash rate. If this does not fix the problem, then further investigation is needed. Chips with an abnormal hash rate can be identified by looking at the test fixture’s log, and they should be replaced directly. However, if any of the chips have recovered their hash rate after re-flashing their EEPROM file, then they do not need to be replaced.

Replacing chips with low or 0 hash rate

Replacing chips with low or 0 hash rates is a common issue when dealing with ASIC mining hardware. The first step to resolving this problem is to re-flash the EEPROM file, as it stores all of the operation information for the ASIC chip and can affect its hash rate if it becomes corrupted. If this doesn’t work, then you may need to replace the chip itself. You should use a hashboard tester to perform chip detection and determine which one needs replacing based on the test results. After locating the faulty chip, you will need to re-solder it to function correctly again before performing fixture tests multiple times until your board passes them successfully. Finally, create maintenance records for feedback before installing your entire miner back together again.

Re-flashing the EEPROM file before replacing chips

Re-flashing the EEPROM file before replacing chips is a beneficial troubleshooting method for Antminer S17+ hash boards. When an error in the EEPROM chip program of the hash board occurs, re-flashing it can help to restore normal operations and determine if any further repairs are needed. After re-flashing, performing a fixture test will help identify abnormal hash rates and pinpoint which chips need to be replaced. This process ensures that only necessary repairs are done, helping to minimize time and costs while also ensuring optimal performance of the miner.

Performing fixture tests after re-flashing and chip replacement

Performing fixture tests after re-flashing and chip replacement are essential steps in repairing a hash board for an Antminer S17+. After re-flashing the EEPROM file, it is essential to do a fixture test to ensure that the chips on the hash board are working correctly. If any chips have abnormal hash rates, they should be replaced accordingly. Once all repairs have been completed, maintenance records should be prepared and provided to production, after-sales, research and development departments. Finally, it is necessary to install the entire miner for conventional aging before finalizing the repair process.

Tips on Troubleshooting ASICs to Avoid Future Issues

Troubleshooting ASICs can be a daunting task for novice miners. While it is essential to identify any problems with your mining hardware, it is equally important to take preventative measures to avoid future issues. Here are some tips on troubleshooting ASICs to keep your miner running smoothly and efficiently.

First, ensure that the power source is adequate for the type of ASIC you are using and that all connections are secure and properly connected. Second, check all components, including fans, heat sinks, PCBs, etc., and their respective temperatures to ensure proper airflow within the unit. Additionally, inspect the firmware of your device regularly to make sure there are no bugs or outdated versions disrupting performance levels. Finally, use diagnostic tools such as hash rate monitors or stress tests to detect any potential issues before they become major problems down the road. By following these simple steps when troubleshooting ASICs, you will increase efficiency while reducing downtime due to hardware malfunctions or other technical difficulties.


Mining and troubleshooting ASICs can be a complicated process. To ensure that your mining hardware is running smoothly, it’s essential to take preventative measures such as checking the power source and connections, inspecting components for proper airflow, and regularly monitoring firmware updates. Additionally, using diagnostic tools like hash rate monitors or stress tests can help you detect any potential issues before they become significant problems. With these steps in mind, you should have no problem keeping your miner up and running while achieving maximum efficiency with minimum downtime due to technical difficulties.

Share the Post:

Disclaimer: The information provided on this blog is for informational purposes only and should not be taken as any form of advice.

Related Posts