Bitmain Antminer S19e XP Hyd. two-bin reference
Official Antminer S19e XP Hyd. version 10 reference covering 240 and 251 TH/s, 5,280-5,522 W, 22 J/TH and exact three-phase coolant requirements.
Quick answer
The Bitmain Antminer S19e XP Hyd. two-bin reference is a Bitcoin miner rated about 240-251 TH/s at roughly 5,280 W (about 22 J/TH).
Full Specifications
| Model | Bitmain Antminer S19e XP Hyd. two-bin reference |
|---|---|
| Model Number | Antminer S19e XP Hyd. version 10 |
| Manufacturer | Bitmain |
| Algorithm | SHA-256 |
| Hashrate | 240-251 TH/s |
| Power Consumption | 5,280-5,522 W |
| Cooling | Hydro |
| Voltage Range | 380-415 V AC three-phase; 50-60 Hz |
| Operating Temperature | 20 C to 50 C inlet coolant |
| Dimensions | 410 x 170 x 209 mm |
| Weight | 12.8 kg net |
| Interface | RJ45 Ethernet 10/100M |
| Status | OEM support reference |
Official two-bin hydro reference: Bitmain documents the Antminer S19e XP Hyd., version 10, in 240 and 251 TH/s bins. The matching typical wall-power ratings at 35°C inlet coolant are 5,280 and 5,522 W; both are rated at 22 J/TH.
| Nominal bin | Typical wall power at 35°C inlet | Rated efficiency |
|---|---|---|
| 240 TH/s | 5,280 W | 22 J/TH |
| 251 TH/s | 5,522 W | 22 J/TH |
Actual hashrate is ±3%; wall power and efficiency are ±5%. This matrix is not a continuous tuning range. Confirm the complete version and rated bin on the physical nameplate.
Three-phase electrical requirements
The official input is 380–415 V AC three-phase, 50–60 Hz, with 12 A maximum current. Bitmain’s conformity record identifies a three-phase-plus-protective-earth connection. Do not transfer 200–240 V air-cooled assumptions to this server.
Facility design requires qualified distribution, grounding, overcurrent protection, isolation, connectors, pumping, heat rejection, monitoring, and emergency controls sized from the exact nameplate and installation conditions.
Exact coolant-loop requirements
Bitmain specifies 20–50°C inlet coolant, 8–10 L/min flow, no more than 3.5 bar pressure, and an OD10 connector. Never energize the server dry or without validated circulation, fluid quality, filtration, heat rejection, leak detection, and emergency isolation.
The official specification lists antifreeze, pure water, and deionized water with pH ranges of 7–9, 6.5–7.5, and 8.5–9.5 respectively. Follow the current exact manufacturer document for fluid selection and maintenance.
Physical, network, and environmental reference
The unpackaged server is 410 × 170 × 209 mm and 12.8 kg net. Packaged dimensions are 570 × 316 × 430 mm and gross weight is 14.1 kg. Network access is RJ45 Ethernet 10/100M. The listed storage range is −20–70°C and relative humidity is 10–90% non-condensing.
Exact-name compatibility boundary
S19e XP Hyd., S19 XP Hyd., S19 XP+ Hyd., and air-cooled S19 XP are separate identities. Matching “XP,” chassis appearance, or hashrate does not establish the PSU, control board, hashboard, firmware, recovery image, connector, coolant procedure, or facility requirements.
Firmware, recovery, and repair
- Identify the exact suffix, version, control board, PSU label, and installed firmware.
- Use only a manufacturer file whose exact product and board scope match the physical unit.
- For no boot, coolant alarms, leakage, corrosion, unstable hashing, interrupted writing, package mismatch, or electrical and thermal symptoms, request Antminer diagnosis.
Primary sources: Bitmain S19e XP Hyd. specification, official product manual, and certificate of conformity. Reviewed August 27, 2026.