Bitmain Antminer S19 XP Hyd. k0-10 reference
Official current Antminer S19 XP Hyd. k0-10 reference: 257 TH/s, 5,346 W and 20.8 J/TH with exact three-phase, coolant and physical requirements.
Quick answer
The Bitmain Antminer S19 XP Hyd. k0-10 reference is a Bitcoin miner rated about 257 TH/s at roughly 5,346 W (about 20.8 J/TH).
Full Specifications
| Model | Bitmain Antminer S19 XP Hyd. k0-10 reference |
|---|---|
| Model Number | Antminer S19 XP Hyd. k0-10 |
| Manufacturer | Bitmain |
| Algorithm | SHA-256 |
| Hashrate | 257 TH/s |
| Power Consumption | 5,346 W |
| Calculated nominal efficiency | 20.8016 J/TH |
| Cooling | Hydro |
| Voltage Range | 380-415 V AC three-phase; 50-60 Hz |
| Operating Temperature | 0 C to 40 C ambient |
| Dimensions | 410 x 170 x 209 mm |
| Weight | 12.8 kg net |
| Interface | RJ45 Ethernet 10/100M |
| Status | OEM support reference |
Current official hydro reference: Bitmain’s current Antminer S19 XP Hyd. specification identifies version k0-10 at 257 TH/s typical, 5,346 W typical at 35°C inlet water, and 20.8 J/TH. Actual hashrate is ±3%; wall power and efficiency are ±5%.
This reference does not broaden the k0-10 rating into undocumented historic bins. Confirm the full printed model, version, and nameplate values on the unit.
Three-phase electrical requirements
The official input is 380–415 V AC three-phase, 50–60 Hz, with 12 A maximum current. This is not compatible with the 200–240 V assumptions used by air-cooled S19-family equipment. Use qualified distribution, grounding, overcurrent protection, isolation, and installation engineering for the exact nameplate.
Exact liquid-loop requirements
Bitmain specifies 20–40°C coolant inlet temperature, 8–10 L/min flow, no more than 3.5 bar pressure, and an OD10 connector for this k0-10 reference. Never energize the server without validated circulation, heat rejection, leak detection, water quality, and emergency isolation.
The current specification lists antifreeze, pure water, and deionized water with different pH boundaries: 7–9, 6.5–7.5, and 8.5–9.5 respectively. Fluid selection and maintenance must follow the current exact manufacturer document; do not transfer chemistry from another hydro model.
Physical, network, and storage reference
The bare server is 410 × 170 × 209 mm and 12.8 kg net; packaged dimensions are 570 × 316 × 430 mm and gross weight is 14.1 kg. Network access is RJ45 Ethernet 10/100M. The listed storage range is −20–70°C and relative humidity is 10–90% non-condensing.
Exact-name compatibility boundary
S19 XP Hyd., S19 XP+ Hyd., S19e XP Hyd., and air-cooled S19 XP are separate names. Matching hashrate alone does not establish the PSU, control board, hashboard, firmware, recovery image, connector, coolant procedure, or facility requirements.
Firmware, recovery, and repair
- Identify the exact suffix, version, control board, and installed firmware.
- Use only a manufacturer file whose exact product and board scope match the unit.
- For no boot, package mismatch, interrupted writing, coolant alarms, leakage, corrosion, instability, or electrical and thermal symptoms, request Antminer diagnosis.
Primary sources: Bitmain S19 XP Hyd. specification and official product support hub. Reviewed August 27, 2026.