Bitcoin accepted at checkout | Ships from Montreal, QC, Canada | Expert support since 2016
$79.99 CAD
The most complete single-piece capture in the line. A full S19 exhaust-end wrap, extended by a 30 mm lip along the side to catch the spill coming off the power supply — the heat that a normal shroud leaves behind because it is not coming out of the fans.
High Demand — Pre-order Now, Ships in 5-10 Business Days
Purchase details
Save 3% when you pay in Bitcoin.
Use the S19 / T19 cluster to connect the product page, specs, maintenance guide, repair service, and compatible high-value parts. These BM1398 machines share hashboard, control board, and APW12 power parts.
The most complete single-piece capture in the line. A full S19 exhaust-end wrap, extended by a 30 mm lip along the side to catch the spill coming off the power supply — the heat that a normal shroud leaves behind because it is not coming out of the fans.
Built around the Antminer S19 series exhaust end with a side-mounted PSU. The 30 mm lip captures side spill rather than fully enclosing the power supply — a complete PSU capture in one piece is not physically achievable at a printable size, and we would rather ship the honest 90 percent than promise something geometrically impossible. Standard 6-inch collar.
Measure before you order. Fit dimensions in this line are derived from published fan and chassis geometry and are not yet validated against measured production hardware. Check your flange size and the clearance around your machine against the footprint in the specifications below. If something does not fit, tell us — that is how the next revision gets better.
Fit it over the exhaust end with the lip oriented toward the PSU side. For a full PSU capture, pair a plain shroud with the dedicated 4-inch PSU exhaust shroud and merge the two lines with a Y-splitter — that combination captures more than this does, at the cost of two parts and an extra duct.
Once you have wrapped the fan end, the PSU becomes the largest uncaptured heat source on the machine, and it is usually sitting in the worst-ventilated corner of the install. The spill lip catches a meaningful share of that in the same single body, with no second duct and no extra fittings. For an S19 living in occupied space, it is the closest thing to complete containment available as one part.
| Fits | Antminer S19 series with side-mounted PSU — full wrap plus 30 mm side spill lip |
|---|---|
| Intake | 2 × 120 mm fans + PSU side spill |
| Outlet | 6″ duct collar |
| Footprint | 325 × 200 × 190 mm |
| Material | PETG |
| Construction | Single continuous body — no assembly, no fasteners, no glued joints |
| Design files | Open source — free to download, use, modify and redistribute |
| SKU | DC-SHR-S19PSU-6 |
Every shroud D-Central designs is released as an open file. The geometry for this part is free to download from our 3D models download center: use it, modify it, remix it, run it in your own shop, sell what you make from it. There is no licence to buy and no design gated behind a purchase. Shared knowledge is the whole reason this industry has open hardware at all, and we are not going to be the ones who stop passing it on.
This listing is for the finished part: made to order in PETG and shipped from Montreal, Quebec. If you would rather have it in your hands than spend an evening making one, buy it here — that is what pays for the next design in the line. You can also support the open-source work directly through D-Central’s fund page.
See the full D-Central shroud and ducting system for the compatibility matrix and sizing guide.
Because it does not fit. A true full-capture body around an S19 and its power supply comes out at over 400 mm on its longest axis, which exceeds what can be produced as a single piece on any realistic machine. We built and tested that geometry, confirmed it was not shippable, and designed this instead. The alternative is a plain shroud plus the 4-inch PSU shroud on its own line.
A meaningful share of the side spill, not all of it. We have not quantified it and we are not going to invent a percentage. If total capture is the requirement, use the two-part approach with a dedicated PSU duct.
It is among them — 325 mm on its longest axis. Check your clearance carefully, including anything mounted above or beside the machine.
If you are capturing this much, take the 8-inch version unless space genuinely forbids it. More captured air needs more duct.
| Weight | 450 g |
|---|---|
| Dimensions | 32.5 × 20 × 19 cm |
Only logged in customers who have purchased this product may leave a review.
When Bitmain announced the Antminer S21, the Bitcoin mining world took notice. After years of incremental improvements across the S19 lineup, the S21 represents a genuine generational leap…
In the rapidly evolving world of cryptocurrency, Bitcoin mining has emerged as a cornerstone activity for enthusiasts and investors alike.
Industrial mining hardware was never built for your house. 3D printing closes the gap — shrouds, enclosures, stands, and repairs. Here is what to print, what to buy, and where the limits are.
We use cookies to improve your experience and analyze site traffic. Privacy Policy
Choose which cookies you allow. Essential cookies are required for the site to function and cannot be disabled.
Required for basic site functionality, shopping cart, and security. Always active.
Help us understand how visitors use our site so we can improve your experience. Includes Google Analytics.
Used to deliver relevant ads and track campaign performance across platforms.
Reviews
There are no reviews yet.